Trial Orders No Longer Wait For A Gap: Aluminum E-Motorcycle Production Gets Its Own Schedule

Oct 30, 2026

Leave a message

20261030151012147518

A thirty-unit enquiry rarely earns a slot at a plant building hundreds of thousands of units a year. The line is running volume; a trial order either squeezes into a gap or waits, and nobody on the sales side can say how long. Separating aluminum frame welding and e-motorcycle assembly onto their own line settles that first: small orders get a place in the schedule instead of competing for one.
An order starts with configuration. Frame specification, handlebar and saddle type, colour and decal position are fixed at this point, and sampling follows. Up to five sample units take less than half a production day, and the buyer decides on volume after handling the real thing; once approved, the same parameters go into a small batch run rather than being retested in a second system.
Welding an aluminum frame is difficult mainly because the material moves heat away so fast. Energy entering the parent metal spreads out, the pool cools quickly, and porosity and lack of fusion follow; once the joint cools, the metal beside it is softer than the base, and the head tube to main beam junction is where that shows first. The answer is to govern heat input rather than raise current: wipe off oxide film and oil before striking, use AC TIG or pulsed MIG with a fine droplet transfer, and run the seams in rotation so heat has somewhere to go. Straightening waits until the workpiece is cold, because bending it hot locks stress into the joint, and that stress surfaces only after the vehicle is assembled.
Whether assembly goes together first time depends on three dimensions: wheelbase, head tube angle and rear dropout spacing. Get the wheelbase wrong and the wheels never share a line; shift the head tube angle and steering turns heavy or vague; let the spacing drift and the wheel set has to be forced in. A fixture station after welding checks all three on every frame, sending out-of-tolerance units to rework instead of packing, and logs current, pass sequence and straightening allowance by batch, so a batch-wide drift can be traced to a lot and a shift.
Frames come off welding into pre-treatment: degreasing, alkaline etching, neutralising, two rinses, drying. Skip one and the coating will not hold. Powder or liquid coating and curing follow. Aluminum does not rust, but it is less forgiving about surface cleanliness, so bath concentration and temperature are watched closely, or a batch leaves with patchy colour and a lower adhesion grade. Coating sits in the same building as welding and assembly, so e-motorcycle frames are never trucked to an outside shop, and a confirmed colour returns to final build the same day.

20261030151012147318
Assembling an e-motorcycle is fussier than an e-bike. Battery compartment tolerance decides whether the pack locks home and how far the damper compresses; harnesses for controller, instruments and lights run along the inner frame wall and are clipped so they cannot rub the fork on full lock; front and rear brakes are set to match in feel, and lights, horn and the brake cut-off switch are energised unit by unit. A rain and power-on check closes final build, and nothing is packed until insulation, lighting, braking and steering pass.
A daily figure alone does not describe capacity. This line runs one shift and rolls about 25 units off a day, a little over nineteen minutes each; on the current order mix it schedules sixteen days a month for roughly 400 units, and filling all twenty-six days would take the same line to about 650. Twenty-five is the ceiling, four hundred is what this month actually produces, and the pair only makes sense together. Lead time follows the same slope: a hundred units hold four production days, and with coating, packing, testing, inspection and loading the buyer usually has goods in one to two weeks; four hundred units is close to a month of output and leaves in about three weeks.
Room to configure is what the shipping side gains. One order can carry several colours and several branding schemes, scheduled and packed in batches and then shipped as full containers; a buyer who wants a single container to test a market, and a repeat order if it sells, is equally workable here. Buyers who want to see the plant can walk the welding stations, coating line, final build and finished-goods area while production runs, and measure wheelbase, head tube angle and weld appearance on the floor - for an e-motorcycle, those three say more than any brochure.
Small orders and volume orders competing for one line is a real delivery constraint in many plants; scheduling them apart is what keeps a steady rhythm. Guangzong Zhaoyue Factory, a Tianhang Group vehicle base in Hebei operated by Hebei Xiaotianhang Bicycle Co., Ltd., runs this aluminum welding and e-motorcycle build line for exactly that kind of work: private label, colour and configuration changes, shipment by the full container, and open access for buyer audits, with practical, reliable two-wheel mobility products for customers at home and abroad.
Contact
Tianhang Group · Hebei Xiaotianhang Bicycle Co., Ltd. · Guangzong Zhaoyue Factory Nickie | +86 19322014900 | nickie@hbxiaotianhang.com

Send Inquiry
Contact us

Looking to source direct from the factory? 20 years of bicycle manufacturing,
80,000 m² factory of our own. Share your requirements and we'll come back with a plan.

Contact the factory!